Outdoor Carpet Adhesive

Houzz

TEC® Skill Set™ Outdoor Carpet Adhesive is specially formulated for the installation of most outdoor carpets and synthetic grass with backings such as marine grade, ACTIONBAC®, rubber-backed, and non-backed. It is water resistant when cured and is for use indoor and outdoor.

  • Solvent-free
  • Easy to spread
  • Excellent bond strength
  • Highly water resistant when cured
  • Environmentally Friendly: Certified to meet CRI's highest standards for indoor air quality
  • Available in 1 quart and 1 gallon pail

 

Outdoor carpet adhesive
Hide reviews

Rate this item

*Name
*City
*Email (will not be published)

Terms and conditions

Description

Packaging

1 quart (946 mL) plastic pail Product #70-4725-5121
1 gallon (3.78 L) plastic pail Product #70-4725-5021

 

See coverage
 

Suitable Substrates
Follow carpet manufacturer's recommendations.
• Fully cured concrete (on, above, or below grade) which is free
from hydrostatic pressure and moisture vapor emissions
• Exterior grade plywood
• Marble
• Terrazzo
 

Storage
Freeze/thaw stable to 10°F (-12°C). If frozen, slowly bring to room
temperature and stir before using.


Shelf Life
Maximum of 18 months from date of manufacture in unopened container.

 

Description  
Physical State Paste
Color Tan
Odor Nil
Open Time 20-30 min at 75 degree F/ 50% RH
Final Cure 24-49 hrs
VOC/Liter of Material 0 grams (calculated)

 

Surface Preparation
Surface must be sound, smooth, clean and dry. Any cracks and depressions must be patched using a cementitious patching compound. Ensure that the surface is free of waterproofing compounds, sealers,
curing agents, oil, grease, wax, adhesive residue or any other contaminant that may impede adhesion.
All concrete substrates must be tested for moisture and pH prior to flooring installation. The industry standard methods for testing moisture are ASTM F-2170 (RH) or ASTM F-1869 (Calcium Chloride-
MVER). Consult floor covering manufacturer for acceptable RH or MVER. Test for pH in accordance with ASTM F-710. pH range of 7-9 is required. Moisture vapor emissions not to exceed 3 lbs./ 1000 ft2/24 hours (0.015 kg/m2/24 hours).

Application
IMPORTANT: Refer to flooring manufacturer’s installation guidelines for proper application instructions, including trowel size and approximate coverage. Lack of adhesive due to improper trowel size can contribute to bond failure / inadequate bond. Apply only the amount of adhesive that can be covered in 20 minutes. Direct sunlight accelerates adhesive drying time and can minimize the adhesive transfer to carpet backing. After installing, roll the carpet in both directions. A minimum temperature of 50°F (10°C) must be maintained for 48 hours before, during and after installation. Restrict heavy foot traffic or rolling loads for at least 72 hours.


Open Time
20-30 minutes (depending on temperature, humidity, and porosity of substrate). DO NOT ALLOW ADHESIVE TO SKIN OVER. Should skin over occur, scrape up and reapply.
 

Clean-up
Clean up wet tools with soap and water. Use mineral spirits for dried adhesive residue, carefully following warnings on container.

Technical Service
Available Mon–Fri
8:00am–5:00pm CST:

1-800-TEC-9023
(1-800-832-9023)
Send an email

Outdoor Carpet Adhesive SDS

Outdoor Carpet Adhesive SDS-English

Don't Forget These

Universal Skimcoat and Patch

Designed to skim coat, smooth, and level irregularities over most surfaces.

Ultimate Self Leveling Underlayment

Smooths and levels most subfloors prior to all floor covering installations.

Get Answers for Your Tec Projects

Ask A Question

Ready-To-Use Floor Patch

Repairs minor imperfections to the substrate prior to the installation of the floor covering.