Floor Mortar

Houzz

TEC® Skill Set™ Floor Mortar is a non-modified mortar used to install tile on floors over cementitious surfaces in commercial and residential applications. For applications over plywood, exterior applications, or whenever the performance of latex modified mortar is desired, mix with TEC Skill Set Mortar Additive.  

  • For installing over cementitious surfaces
  • Mix with TEC® Skill Set™ Latex Mortar Additive for improved flexibility and adhesion
  • Additive allows bonding to plywood
  • May contribute to LEED® certification project points
Hide reviews

Rate this item

*Name
*City
*Email (will not be published)

Terms and conditions

Download PDF

TEC® Skill Set™ Floor Mortar Product Info

Description

TEC Skill Set Floor Mortar is designed to bond floor tile. Mixed with water, it meets ANSI A118.1 specifications. Mixed with TEC Skill Set Mortar Additive, meets ANSI A118.4 and ANSI A118.11 specifications.

 

Key Benefits and Features

  • For installing over cement surfaces
  • Floors only
  • Mix with Mortar Additive for improved flexibility and adhesion
  • Additive allows bonding to plywood

 

Packaging
50 lbs. (22.68 kg) plastic bag
Gray    Product #70-3289-3121

 

Coverage
Coverage will vary with condition of substrate. Required trowel size will vary with the tile size, type and substrate uniformity. Select the trowel size that will ensure 100% coverage. Figures below are presented only as guidelines.

 

Trowel Size Approximate Coverage
per 50 lbs. (22.68 KG)
1/4" x 1/4" x 1/4"
(6 x 6 x 6 mm)
square-notch trowel
80-90 sq. ft.
(7.4-8.4 m2)
1/4" x 3/8" x 1/4"
(6 x 10 x 6 mm)
square-notch trowel
50-60 sq. ft.
(4.6-5.6 m2)

 

Suitable Substrates
When properly prepared, suitable substrates include:

  • Gypsum wallboard
  • Water resistant gypsum wallboard (greenboard)
  • Cementitious backer units (CBU)
  • Glass mat backer board
  • Adhesive residue (except tacky or pressure-sensitive adhesive)*
  • Cured concrete, cured mortar beds, brick and masonry (if exterior*)
  • APA Grade Trademarked Exposure 1 Plywood [underlayment grade or better, two layers, 11/8" (28 mm) total minimum thickness, interior floors only]*
  • Existing ceramic tile and natural stone, provided existing flooring is well-bonded to an approved substrate.*
  • Vinyl composition tile, asphalt tile, linoleum or non-cushioned vinyl sheet goods* (provided existing flooring is well-bonded to an approved substrate)

 

*Requires use with TEC Skill Set Mortar Additive

 

Storage
Store in a cool, dry area away from direct sunlight. Do not store open containers.

 

Shelf Life
Maximum of 1 year from date of manufacture in unopened package.

 

Limitations
Not for installing green marble or other moisture-sensitive stone tile; use TEC Skill Set Marble Mortar. Not for use over rubber, strip wood floors, oriented strand board, particle board or lauan plywood. For CDX plywood, use TEC Skill Set Mortar Additive with TEC Skill Set Floor & Wall Mortar. Do not apply over single-layer wood floors. Certain natural stone tiles may be affected by mortar shadowing or staining. Test a small area prior to use to determine suitability.

 

Cautions
FIRST AID MEASURES: In all cases, seek medical attention if symptoms develop or persist. EYES: Flush with water for 20 minutes. SKIN: Wash with soap and water. IF VAPORS INHALED: Remove to fresh air. IF SWALLOWED: Do not induce vomiting. WARNING! This product contains chemicals known to the State of California to cause cancer, birth defects or reproductive harm. KEEP OUT OF REACH OF CHILDREN. For Medical Emergency Information, call 1-888-853-1758.

 

This Product Data Sheet has been prepared in good faith on the basis of information available at the time of publication. It is intended to provide users with information about and guidelines for the proper use and application of the covered TEC Skill Set brand product(s) under normal environmental and working conditions. Because each project is different, H.B. Fuller Construction Products Inc. cannot be responsible for the consequences of variations in such conditions, or for unforeseen conditions.

Applicable Standard

Skill Set Floor Mortar
Description ANSI Requirement Typical Results
28 Day Shear Strength ANSI A118.1
Glazed Wall Tile
> 250 psi (1.7 MPa) 250-300 psi (1.7-2.1 MPa)
Impervious Ceramic Tile (Porcelain) > 150 psi (1.0 MPa) 150-200 psi (1.0-1.4 MPa)
Quarry Tile > 100 psi (0.7 MPa) 150-225 psi (1.0-1.5 MPa)
Sag on Vertical Surfaces ≤ 1/16" (1.6 mm) 0-1/16" (0-1.6 mm)
Open Time at Room Temperature ≥ 50 minutes 50 minutes
Adjustability at Room Temperature ≥ 30 minutes 30 minutes
Final Set 9-15 hours 9-15 hours
Description ANSI Requirement Typical Results when mixed
with TEC Skill Set Mortar Additive
28 Day Shear Strength ANSI A118.4
Glazed Wall Tile
> 300 psi (2.1 MPa) 500-600 psi** (3.4-4.1 MPa)
Impervious Ceramic Tile (Porcelain) > 200 psi (1.4 MPa) 225-300 psi (1.5-2.1 MPa)
Quarry Tile > 150 psi (1.0 MPa) 350-450 psi (2.4-3.1 MPa)
Sag on Vertical Surfaces ≤ 1/16" (1.6 mm) 1/16" (1.6 mm)
Open Time at Room Temperature ≥ 50 minutes 60-80minutes
Adjustability at Room Temperature ≥ 30 minutes 30-40 minutes
Final Set 9-15 hours 9-15 hours

 

** ANSI-specified glazed wall tile failed at 600 psi (4.1 MPa)

 

Physical Properties

Description  
Physical State Dry powder
Color Available in gray
Pot Life 2 to 3 hours
Initial Cure [at 72°F (22°C)] 16 to 24 hours
Final Cure 21 days
Foot Traffic Rating (ASTM C627) Residential to Extra Heavy Commercial
(depending on substrate)

Mortar Installation Instuctions
All substrates must be dry, structurally sound with maximum deflection per industry standards of L/360 for ceramic tile installations and L/720 for natural stone installations under all live and dead loads; and be free from oil, grease, dust, paint, sealers or concrete curing compounds. All contaminants should be removed prior to installation of tile. Surface protrusions and tile glazes shall be removed by sanding, scraping or scarifying. After preparation, remove all dust by vacuuming. Note: Vinyl asbestos tile or any substrate containing asbestos shall not be sanded, scored or scarified because of the potential health hazard of breathing dust. Any substrate containing asbestos must be handled in accordance with existing EPA regulations. Contact your local EPA office.

 

Notes: Expansion joints must be provided in the tile work over all construction, control and expansion joints in the backing and where backing materials change. Follow ANSI A108.01 Section 3.7 Requirements for Expansion Joints.

Maximum variations in all substrates must not exceed 1/4" in 10 ft. (6 mm in 3 m) or 1/16" in 1 ft. (1.5 mm in 0.3 m) from the required plane. For non-level, interior surfaces use TEC® Skill Set™ Self Leveling Underlayment.

 

Mixing-With Water
For best results, maintain all tiling materials, substrates, room and adhesives at 50°-70°F (10-21°C) for 24 hours before and 48 hours after installation. Avoid breathing dust and contact with eyes and skin. Avoid using high speed mixing, not to exceed 300 rpm, to prevent entraining air. Add powder to liquid for ease of mixing.

In a clean mixing container, slowly add product to 4.5 to 6 quarts (4.26-5.68 L) clean, cool water. Mix material for 2-5 minutes to a thick creamy consistency, then allow the mortar to stand for 10 minutes. Remix for 1-2 minutes and apply.

 

Mixing-With Latex Additive
For improved performance in any application, H.B. Fuller Construction Products Inc. recommends the use of TEC Skill Set Mortar Additive in place of water. For installations subjected to freeze/thaw conditions; bonding over most non-cementitious substrates; installation of porcelain tile; or any ANSI A118.4 or ANSI A118.11 latex mortar project, the use of TEC Skill Set Mortar Additive is required.

When using a mortar additive, always follow label directions for detailed mixing and substrate recommendations.

 

Application
Apply mortar using flat side of trowel to promote better substrate contact, then comb in one direction with the notched side of the trowel. Spread only an area that can be tiled while surface is still tacky (typically 20-30 minutes). Press tiles into setting bed, then push in a direction perpendicular to the notched trowel ridges to achieve optimum coverage. Apply mortar in a heavy enough layer so that complete contact (no voids) between mortar and tile is accomplished when tile is positioned. It may be necessary to "back-butter" large tiles to achieve complete coverage and firm support. Periodically remove and check a tile to assure proper coverage. Keep a minimum of 2/3 of the joint depth between tiles for grouting.

Open time and tile hand adjustability may vary with job site conditions. Stir occasionally during use to maintain the smooth, creamy consistency of the product. Do not add additional water.

 

Drying Time
Grouting may be accomplished when tiles are held firmly in place, typically 16 to 24 hours after installation is completed. No traffic is permitted over the tiles prior to grouting. Cold temperatures or high humidity may extend curing time. Unglazed tiles may require sealing prior to grouting so discoloration will not occur. The use of TEC grout products are highly recommended. DesignColor™ Grout mixed with Grout Boost® Stain Resistant Grout Additive or Power Grout™ are available in a wide array of designer colors, these products provide stain resistance, high performance and ease of use.

 

Clean-up
Clean tools, hands, and excess materials from face of tile, while mortar is still fresh, with warm soapy water.

Technical assistance information is available by calling the Technical Service Helpline.

Toll Free: 800-832-9023

TEC® Skill Set™ Floor Mortar Safety Data Sheet

 

 Download the TEC® Skill Set™ Floor Mortar Safety Data Sheet

Don't Forget These

Latex Mortar Additive

TEC® Skill Set™ Mortar Additive is used in place of water with non-modified TEC Skill Set brand mortars. Use mortar additive with TEC Skill Set non-modified mortars.

TEC® Power Grout®

TEC® Power Grout® maximizes grout performance while providing ease of use. It is highly stain resistant and provides strong, color consistent joints.

Get Answers for Your Tec Projects

Ask A Question

Unsanded Grout

TEC® Skill Set Unsanded Grout is a polymer-enhanced, Portland cement grout for grouting joints up to 1/8” wide.

Unsanded Grout

TEC® Skill Set Unsanded Grout is a polymer-enhanced, Portland cement grout for grouting joints up to 1/8” wide.